Down hill braking retarder stator assembly B5-22 and B5-21

Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

The diameter of this 008 flange is 162.5mm, the flange screw is M16, and the drive shaft screw is M16. Our retarder flanges are specifically engineered to optimize braking power. By providing additional braking force, they help reduce vehicle speed effectively, even in demanding conditions.
Crafted from high-quality materials, our retarder flanges are built to withstand extreme temperatures, heavy loads, and continuous usage. Count on their durability and reliability to deliver consistent performance over an extended period.

The manual switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque , 4th gear represents 3/4 of the maximum retarding torque, and 5th gear represents the maximum retarding torque.
The retarder handle switch is installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.

TELMA brand DX series eddy current retarder installed in the gearbox or rear axle. There are seven models.

Product Introduction：
1. Lightweight and miniaturized dual-rotor design, light weight, low moment of inertia, small dynamic load, and no impact on the transmission system;
2. Stable torque output performance;
3. Diversified matching and wide application;
4. The structure size is small, and the dual-rotor retarder is used to solve the problem of the layout of the drive shaft of the small and medium-sized vehicle;
5. The rotor is made of alloy steel casting;
6. The coil adopts special heat shrinkable material;
7. The stator tray is die-casted with high-density aluminum alloy material that is abundant in South America.

The control unit of an eddy current retarder is a vital component responsible for managing and regulating the operation of the retarder system. Eddy current retarders are braking systems commonly used in heavy-duty vehicles to provide efficient and reliable braking force.
The control unit acts as the central intelligence of the eddy current retarder system, interpreting sensor inputs, processing signals, and regulating the braking force to ensure smooth and efficient operation. Its functionality is crucial in providing effective braking performance, enhancing vehicle safety, and optimizing overall vehicle dynamics.We are now ready to start production.

The DHZ series eddy current retarder assembly suitable for vehicles with front engine and installed in the middle of two drive shafts. DHZ series consists of 11 models. The dual-rotor intermediate bearing support structure is adopted, which is convenient to install and has little impact on the original vehicle transmission system. Imported bearings and high temperature resistant grease are used to ensure the safe and reliable operation of the retarder. It can be used as a chassis dynamometer and a controllable load.

Retarder parts TERCA 8153 Y controller relayblock is high quality. Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

TELMA A series eddy current retarder suitable for all kinds of vehicles with long drive shafts. Installed in the middle of the drive shaft.

Product Introduction：
1. Lightweight, miniaturized dual-rotor design, light weight, low moment of inertia, small dynamic load, and no impact on the transmission system;
2. Stable torque output performance;
3. Diversified matching and wide application;
4. The structure size is small, and the dual-rotor retarder is used to solve the problem of the layout of the drive shaft of the small and medium-sized vehicle;
5. The rotor is made of alloy steel casting;
6.The coil adopts special heat shrinkable material.

The diameter of this FV61-30 E-shaped shaft flange is 162mm, the flange screw is M14, and the drive shaft screw is M12.
Our retarder flanges are designed for easy installation, minimizing downtime and maximizing productivity. With clear instructions and compatibility with standard braking systems, integrating our flanges into your existing setup is a seamless process.

Retarder parts TERCA 8429 controller relayblock is high quality. Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

As technology continues to advance, modern eddy current retarder controllers incorporate sophisticated features such as intelligent control algorithms, integrated sensors, and communication interfaces.
One key advantage of eddy current retarder controllers is their ability to offer progressive and smooth braking. Unlike traditional braking systems that can cause abrupt stops, eddy current retarders provide gradual deceleration, minimizing wear on brake components and increasing overall safety.
In conclusion, eddy current retarder controllers are integral components in the realm of braking systems, offering efficient and reliable deceleration for heavy-duty vehicles. With their electromagnetic principles and advanced control capabilities, these controllers pave the way for improved safety, reduced maintenance, and optimized braking performance.

Model number TR10 retarder stator coil assembly is a product of the famous Chinese retarder brand TERCA. The TR10 retarder stator is specially fitted in gearboxes.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame. The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

DHB-15A stator coil assembly is suitable for CAMA DHB series eddy current retarder. CAMA DHB series eddy current retarder suitable for long-distance and tourist buses with rear gearboxes.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The diameter of this CAMA current vortex retarder flange for end face is 182mm, there are 8 holes, the flange screws are M16, and the drive shaft screws are M14.
Crafted from high-quality materials, our retarder flanges are built to withstand extreme temperatures, heavy loads, and continuous usage. Count on their durability and reliability to deliver consistent performance over an extended period.

The brand name of F191 and 71-95 brake retarder stator assembly is TELMA. The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame. The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

AX5 Series Eddy Current Retarder Suitable for All Kinds of Vehicles with Long Drive Shafts. The AX5 series comes in two models, AX50-70 and AX51-00.

AX5 Series Product Introduction：
1. Lighter, smaller and better performance;
2. Uniquely designed rotor to enhance torque durability and reduce loss;
3. Optimized current design to reduce current loss;
4. More corrosion resistant;
5. Modular design, longer use time;
6. It is installed in the middle of the drive shaft and has wide applicability.

The diameter of this 043 flange is 182mm, the flange screw is M16, and the drive shaft screw is M14.
Investing in our retarder flanges is a cost-effective solution to improve braking performance. By reducing wear and tear on standard brake systems, our flanges can extend their lifespan and minimize maintenance costs, ultimately saving you time and money.

The DHQ series has five models. DHQ series eddy current retarder suitable for urban buses and medium- and light-duty vehicles with short rear suspension and unable to shorten the drive shaft. It is characterized by its light weight and low power consumption. The 12 coils are distributed radially, the installation size is small, and the low-speed performance is good. The excitation gap does not need to be adjusted, and a small amount of string movement along the axial flange does not affect the use. The rotor adopts a single-rotor drum structure and is cast with special high-temperature alloy, which is light in weight and small in deformation.

The diameter of this TERCA retarder ring flange is 95mm, the thickness is 22.5mm, there are 8 holes, and the drive shaft screws are M16.
Investing in our retarder flanges is a cost-effective solution to improve braking performance. By reducing wear and tear on standard brake systems, our flanges can extend their lifespan and minimize maintenance costs, ultimately saving you time and money.

TB-11 series retarder stator is suitable for TERCA TB series eddy current retarder.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The stator frame is evenly equipped with 8 stator core, the stator core is wound with a coil, the stator frame is evenly opened with 8 core holes, the stator core is inserted in the hole and fixed on the stator frame, the two side segments of the extended core hole of the stator core are symmetrically distributed on both sides of the stator frame; Both ends of each stator core are fixedly connected with magnetic conductive plates.

The TR series includes 4 models. Compact structure, light weight, small size, easy to disassemble and assemble; The rotor adopts a cylindrical structure, a fully machined surface, and a beautiful appearance; Low power consumption, no need to replace the original car generator; The braking torque is large, 100-300NM larger than other similar structure eddy current retarders, and the maximum braking torque can be reached at low speed (vehicle speed is about 15km/h); Radial distribution, so that the rotor gap is not affected by the bearing movement, making the eddy current retarder run more reliable and more widely matched; The axial length is small, the weight of the rotor is light (about 20kg), and the impact on the original vehicle’s transmission system is small; The installation space required is small, especially suitable for medium-sized vehicles with short rear suspension and unable to shorten the drive shaft; Adopt digital and intelligent control system, safer work and more reliable operation.

The TM series eddy current retarder suitable for all kinds of vehicles with long drive shafts, installed between two drive shafts; TM series includes six models. The use of intermediate bearing structure has almost no impact on the vehicle chassis; Equipped with imported bearings and high temperature resistant grease, long service life; Adopt the best structural scheme, the gap adjustment is simple, and the maintenance is convenient; High electric power, low power consumption; The braking torque is large, the torque range is wide, and the maximum braking force is from 500-3500NM; Suitable for all kinds of medium and heavy passenger, trucks and special vehicles with long drive shafts; Adopting digital and intelligent control system, it is safer to use and more reliable for all work.

The diameter of this TB24 flange is 182mm, the thickness is 45mm, the flange screw is M16, and the drive shaft screw is M16.
We understand that different vehicles and applications have unique requirements. That’s why we offer customizable options, allowing you to select the retarder flange that best suits your specific needs. From size and shape to material composition, we can tailor our product to match your exact specifications.

The diameter of this TR10 retarder flange for 153 rear axle is 166mm and the thickness is 28mm.
Whether you operate a fleet of commercial trucks, heavy machinery, or specialized vehicles, our retarder flanges are engineered to optimize your braking system’s efficiency. Experience the difference in braking performance and safety with our high-quality retarder flanges.

There are seven models in the DHB series eddy current retarder. Suitable for long-distance and tourist buses with rear gearboxes. The stator is made of aerospace die-cast aluminum alloy, which is anti-magnetization, high strength, light weight and good size stability. The rotor is made of special high-temperature resistant alloy casting, with small deformation and no remanence; the heat dissipation channel adopts a multi-layer structure, which has large ventilation and small thermal decay.

Installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.
When the car is ignited, the retarder is in a standby state. When the car needs to be slowed down, the purpose of slowing down can be achieved by turning the handle of the manual switch to the required gear step by step. If you want to turn off the slowing down function, just use the handle Turn the control switch handle back to 0 gear.

DX1500 retarder stator coil assembly is suitable for TELMA DX series eddy current retarder.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The main function of the stator is to generate a rotating magnetic field, while the main function of the rotor is to be wire-cut in the rotating magnetic field to generate a current.

The diameter of this 043 flange for end face is 182mm, the flange screw is M16, and the drive shaft screw is M14.
We understand that different vehicles and applications have unique requirements. That’s why we offer customizable options, allowing you to select the retarder flange that best suits your specific needs. From size and shape to material composition, we can tailor our product to match your exact specifications.

Experience the pinnacle of wiring technology with the Retarder B Series Four Pillars Wiring Board. Designed to deliver unmatched connectivity and performance, this groundbreaking wiring board is set to revolutionize electrical systems.
With its advanced design and cutting-edge features, the Retarder B Series Wiring Board seamlessly integrates with four pillars retarders, enabling smooth and efficient power transmission. This wiring board is engineered for optimal performance, minimizing energy loss and maximizing the overall efficiency of your systems.

Relay Controller is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.