Retarder fittings intelligent control system

The diameter of this 043 flange is 182mm, the flange screw is M16, and the drive shaft screw is M14.
Investing in our retarder flanges is a cost-effective solution to improve braking performance. By reducing wear and tear on standard brake systems, our flanges can extend their lifespan and minimize maintenance costs, ultimately saving you time and money.

The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The stator frame is evenly equipped with 8 stator core, the stator core is wound with a coil, the stator frame is evenly opened with 8 core holes, the stator core is inserted in the hole and fixed on the stator frame, the two side segments of the extended core hole of the stator core are symmetrically distributed on both sides of the stator frame; Both ends of each stator core are fixedly connected with magnetic conductive plates.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

Retarder parts TERCA 8429 controller relayblock is high quality. Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

The TM series eddy current retarder suitable for all kinds of vehicles with long drive shafts, installed between two drive shafts; TM series includes six models. The use of intermediate bearing structure has almost no impact on the vehicle chassis; Equipped with imported bearings and high temperature resistant grease, long service life; Adopt the best structural scheme, the gap adjustment is simple, and the maintenance is convenient; High electric power, low power consumption; The braking torque is large, the torque range is wide, and the maximum braking force is from 500-3500NM; Suitable for all kinds of medium and heavy passenger, trucks and special vehicles with long drive shafts; Adopting digital and intelligent control system, it is safer to use and more reliable for all work.

Model number TR10 retarder stator coil assembly is a product of the famous Chinese retarder brand TERCA. The TR10 retarder stator is specially fitted in gearboxes.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame. The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The AX8 series is divided into AX83-00 and AX83-40 models. AX8 series bus brake eddy current retarder suitable for all kinds of vehicles with long drive shafts.

Product Introduction：
1. Lighter, smaller and better performance;
2. Uniquely designed rotor to enhance torque durability and reduce loss;
3. Optimized current design to reduce current loss;
4. More corrosion resistant;
5. Modular design, longer use time;
6. It is installed in the middle of the drive shaft and has wide applicability.

The eddy current retarder relay block is a critical component within the realm of automotive engineering, specifically in vehicles equipped with eddy current retarder systems. This relay block serves as the central control unit, facilitating the efficient operation and coordination of the various components involved in the eddy current retarder system.
This relay block effectively controls the engagement and disengagement of the eddy current retarder, allowing seamless integration with the vehicle’s overall braking and acceleration systems. It ensures optimal performance, smooth operation, and enhanced safety by monitoring parameters such as vehicle speed, engine RPM, and temperature.

The diameter of this 008 flange is 162.5mm, the flange screw is M16, and the drive shaft screw is M16. Our retarder flanges are specifically engineered to optimize braking power. By providing additional braking force, they help reduce vehicle speed effectively, even in demanding conditions.
Crafted from high-quality materials, our retarder flanges are built to withstand extreme temperatures, heavy loads, and continuous usage. Count on their durability and reliability to deliver consistent performance over an extended period.

The DHZ series eddy current retarder assembly suitable for vehicles with front engine and installed in the middle of two drive shafts. DHZ series consists of 11 models. The dual-rotor intermediate bearing support structure is adopted, which is convenient to install and has little impact on the original vehicle transmission system. Imported bearings and high temperature resistant grease are used to ensure the safe and reliable operation of the retarder. It can be used as a chassis dynamometer and a controllable load.

The retarder handle switch is installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.
The manual switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque , 4th gear represents 3/4 of the maximum retarding torque, and 5th gear represents the maximum retarding torque.

This type of stator assembly is suitable for both B5-17 and TB-15. The retarder parts stator assembly has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The Control Unit monitors key parameters like temperature and system diagnostics to ensure the retarder operates within safe limits. It may also incorporate intelligent algorithms and control strategies to optimize the efficiency of the retarder system, maximizing energy recovery and minimizing wear.
In summary, the eddy current retarder Control Unit acts as the brain of the system, coordinating the operation of the retarder for precise and efficient braking. By intelligently controlling the retarder’s engagement and monitoring critical parameters, it enhances the vehicle’s braking capabilities and contributes to a safer and smoother driving experience.

Prepare to witness a paradigm shift in wiring technology with the groundbreaking Eddy Current Retarder R Series Four Pillars Wiring Board. Engineered to redefine connectivity and efficiency, this revolutionary wiring board is poised to transform the landscape of electrical systems.
The Eddy Current Retarder R Series Wiring Board seamlessly integrates with four pillars eddy current retarders, offering a seamless and optimized power transmission solution. Its state-of-the-art design and precision engineering work in harmony to minimize energy loss and maximize the overall efficiency and performance of your systems.

The control handle switch is installed at the lower right of the steering wheel, it is a multi-functional combination switch, the retarder can be controlled by pulling the retarder handle switch. Installed in the cockpit. The driver realizes the braking of the vehicle by selecting the appropriate gear. Typically mounted on the dashboard or under the steering wheel, it will provide one neutral gear and four to six control gears.
The manual switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque , 4th gear represents 3/4 of the maximum retarding torque, and 5th gear represents the maximum retarding torque.

A controller tester for eddy current retarders is a device used to evaluate the functionality and performance of the controllers used in eddy current retarder systems.
The purpose of the controller tester is to simulate various operating conditions and monitor the response of the controller. It helps in identifying any issues or malfunctions in the controller before it is installed in the actual retarder system. This testing ensures that the retarder operates effectively and safely in real-world scenarios.
By using a controller tester for eddy current retarders, manufacturers, maintenance personnel, and researchers can verify the reliability and effectiveness of the controller before its integration into the retarder system. This testing process contributes to improved safety, performance, and longevity of the eddy current retarder in various applications.

With its advanced technology and precision engineering, the Eddy Current Retarder Terminal Board enables seamless integration of eddy current retarders into your existing systems. Its compact and efficient design ensures reliable and efficient power transmission, minimizing energy loss and maximizing overall system performance.
Experience the benefits of simplified wiring and enhanced control with our terminal board’s intuitive interface, allowing for easy installation and configuration. Say goodbye to complex wiring setups and hello to streamlined operations.

Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

Retarder intelligent control system adopts microcomputer core control of high automation and intelligence degree to adapt to a variety of harsh working environment with long service life.

Product introduction:
Break the traditional relay switch control mode, using non-contact intelligent module control;
Long service life, the number of work can reach more than 15 million times;
Microcomputer core control, high degree of automation and intelligence;
Strong self-protection function. With functions in various aspects, such as over-temperature, over-current, over-voltage and other automatic protection, and brake dragging, open circuit, short circuit detection and alarm;
Can be connected with the ABS system and brake light system of the original vehicle;
Adapt to harsh environments, high reliability. Adapt to environments at the temperature of -40°C ~ 105° C, with waterproof and salt spray corrosion resistance, and vibration resistance performance;
Conducted a rigorous electromagnetic compatibility design, passed the EU directive AUTOMOTIVE EMC certification;
CAN bus based on SAE J1939 protocol, distributed, modular design.

The control unit of an eddy current retarder is a crucial component that plays a key role in the operation and management of the retarder system. It is responsible for monitoring and regulating the braking force generated by the retarder, ensuring safe and efficient braking performance.
The control unit acts as the brain of the eddy current retarder system, processing sensor inputs, generating control signals, and regulating the braking force. Its functionality ensures smooth and reliable braking performance while considering safety, efficiency, and integration with other vehicle systems.

The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The stator frame is evenly equipped with 8 stator core, the stator core is wound with a coil, the stator frame is evenly opened with 8 core holes, the stator core is inserted in the hole and fixed on the stator frame, the two side segments of the extended core hole of the stator core are symmetrically distributed on both sides of the stator frame; Both ends of each stator core are fixedly connected with magnetic conductive plates.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.
TERCA brand 8133 Y controller is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.

The handle switch is divided into 5 gears, 0 means the retarder is closed, 1 means the retarder constant speed gear, 2 means 1/4 of the maximum retarding torque, 3 means 1/2 of the maximum retarding torque, The 4th gear represents 3/4 of the maximum retarding torque, and the 5th gear represents the maximum retarding torque.
When the car is ignited, the retarder is in a standby state. When the car needs to be slowed down, the purpose of slowing down can be achieved by turning the handle of the manual switch to the required gear step by step. If you want to turn off the slowing down function, just use the handle Turn the control switch handle back to 0 gear.

CAMA DHB series eddy current retarder suitable for long-distance and tourist buses with rear gearboxes. DHB-24 retarder maximum torque is 2400Nm and electric current is 24V.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The action of the stator is to produce an alternating current and the action of the rotor is to create a rotating magnetic field.

The diameter of this flange is 162.5mm, the flange screw is M12, and the drive shaft screw is M16.
Whether you operate a fleet of commercial trucks, heavy machinery, or specialized vehicles, our retarder flanges are engineered to optimize your braking system’s efficiency. Experience the difference in braking performance and safety with our high-quality retarder flanges.

This TERCA flange is used to match the 153 rear axle. The black one has a diameter of 166mm and a thickness of 34mm. The white one is 175mm in diameter and 28mm thick.
Crafted from high-quality materials, our retarder flanges are built to withstand extreme temperatures, heavy loads, and continuous usage. Count on their durability and reliability to deliver consistent performance over an extended period.

Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.
It is an electronic control device, which has a control system (also known as an input circuit) and a controlled system (also known as an output circuit), and is usually used in an automatic control circuit. It actually uses a smaller current to control a larger current A kind of “automatic switch”.

TB-11 series retarder stator is suitable for TERCA TB series eddy current retarder.
The stator has several groups of internal coils, which are the main working parts of retarder. It is connected with the chassis of the vehicle through a fixed bracket. The stator is the stationary part of a motor. The stator consists of three parts: stator core, stator winding and frame.
The stator frame is evenly equipped with 8 stator core, the stator core is wound with a coil, the stator frame is evenly opened with 8 core holes, the stator core is inserted in the hole and fixed on the stator frame, the two side segments of the extended core hole of the stator core are symmetrically distributed on both sides of the stator frame; Both ends of each stator core are fixedly connected with magnetic conductive plates.

The contact assembly of the static and dynamic contacts of the relay includes a static contact piece, a moving contact piece, a moving reed piece, a push card, two static contacts and two moving contacts. The dynamic and static contact structure improves the current breaking performance and prolongs the electrical life.
Relay is a kind of electric control device, is when the change of the input quantity to meet the specified requirements, in the electrical output circuit to make the controlled quantity of a predetermined step change of an electrical appliance. Relay has control system and controlled system, usually used in the automatic control circuit, in the circuit plays the role of automatic regulation, safety protection, conversion circuit and so on.

Experience the pinnacle of wiring technology with the Retarder B Series Four Pillars Wiring Board. Designed to deliver unmatched connectivity and performance, this groundbreaking wiring board is set to revolutionize electrical systems.
With its advanced design and cutting-edge features, the Retarder B Series Wiring Board seamlessly integrates with four pillars retarders, enabling smooth and efficient power transmission. This wiring board is engineered for optimal performance, minimizing energy loss and maximizing the overall efficiency of your systems.

The diameter of this TERCA Two-in-one retarder flange is 180mm, there are 4 holes, the flange screws are M16, and the drive shaft screws are M16.
Investing in our retarder flanges is a cost-effective solution to improve braking performance. By reducing wear and tear on standard brake systems, our flanges can extend their lifespan and minimize maintenance costs, ultimately saving you time and money.